Features

• Zones: 16 wireless, 8 wired. All can be renamed as required by sending text messages to the alarm.
  
• Zone Types: typically one sensor per zone -
  
  • Wireless -
    
    • Normal or Stay(Home) x 11. Connect PIRs or Door/Window sensors to these zones.
      
    • 24hr x 3. Used for Smoke, Gas and Water leakage detectors.
      
    • Watch x 1. Elderly Personal Alarm capability to have PIRs check for movement and alarm if nothing is detected within a defined time period.
      
    • SOS x 1. Used for static emergency buttons or for Personal Medical Alarm pendant or wristwatch style emergency buttons.
      
  • Wired - Normal or Stay(Home) x 5, 24hrs x 2, SOS x 1.
• Armed States: Armed, Disarm, Home(Stay), Emergency.
• Independent Output Relay (3A @ 240V AC): Can have a light attached that can be switched on/off by text message. Not activated by alarm condition.
• Alarm Output Relay: Once alarm is activated this will activate for 4 mins. A light could be attached if required.
• Siren: choose whether or not to sound on alarm activation.
• Timers: automatically activate and deactivate at defined times.
• Code Query: Test mode will show which sensor is being activated. Makes set-up easy.
  
• Battery: internal rechargeable battery will provide up to 18hrs power. The siren or output relays will not function whilst on battery power.
  
• Alarm records: view up to 100 events.
• Self Test: will send a text message every 0 - 240 hrs if required. Useful to ensure PAY-as-you-go SIM does not get deactivated if not used.
  
• Arm (Exit) Delay: 0, 20, 30, 60, or 90 secs.
• Alarm (Entry) Delay: 0, 20, 30, 60, or 90 secs.
• Remote ARM & DISARM via text message.
• Auto answers if called. Use it like a mobile phone!
• Time & Date: Allows the time and date to be set so you can identify exact times when alarm has sounded.
• Power Fail and Restore notification: text message sent after power fail of more than 30 mins.
• GSM (mobile phone) signal failure alert: siren will sound if GSM signal is lost or jammed.

Spec

• Rated Voltage: 9 ~ 12VDC 2A.
• Siren Output Voltage: 12VDC.
• Working Temperature: -10°C ~ +60°C.
• Storage Temperature: -20°C ~ +60°C.
• Relative Humidity: 10-90% - No Condensation.
• Working Frequency: Quad Band - 850/900/1800/1900 Mhz.
• Communication Protocol: GSM Phase 2/2 (including data service).
• Wireless sensor receiving frequency: 433.92 Mhz.
• Alarm Link Output Relay: 3A @ 240V AC. Max 700W.
• Max wireless sensors: 16 using separate codes, i.e. 1 per zone; Unlimited if using same code.
• Max Wired Zones sensors: 8. Supports Normally Open (NO), Normally Closed (NC) and EOL type (2.2K resistors must be used - available on request).
• Max Remote Controls: 5. 
• Wireless Range: Max 100m depending on conditions. Typical range 30m - 50m.
• Battery: Built-in lithium-ion battery - 1200mAh@3.7V.
• Battery Standby Time: Max. 18hrs. 
• Width x Depth x Height (cm) approx. = 18 x 3 x 12.5.

Contents

• 1 x Elite Wireless House Alarm System.
• 1 x Enhanced PIR.
• 1 x Door/Window contact (100m).
• 2 x Standard Remote Control Keyfob.
• 1 x Strobe Strobe Siren (Wired).
• 1 x 12vDC power supply.
• 1 x User Manual.
• 1 x External antenna.

Install

Installation is a relatively easy process. Read the Manual and the Quickstart guide for full information on how to use and setup your alarm. We suggest that before you fix any sensors you register them to the control panel and name each zone by sending it a text message as detailed in the user manual. Use the RF Code Query (Menu 1: View --> 7: RF Code Query) to identify which sensor is programmed to which zone. Any sensors that are part of a standard kit will have already been registered.

Consider registering any door/window sensors as 'Stay Zones' and PIRs as 'Normal Zones'. This way the alarm can be set at night and the perimeter is protected but you can still walk about the house.

When attaching PIRs to the corner of a room ensure you observe the recommendations for height. Attach the bracket sufficiently far enough away from the wall so that the sensor can be easily slid onto the bracket. Once tested remember to move the small internal jumper clip from 'test mode' to 'normal mode' or your batteries will be exhausted very quickly.

Unless you have wired sensors connected do not set these or you will find the alarm permanently activates. If this happens call us for an alarm reset code.